KAD/ARR/101 ARINC 664 Part 7 (A664P7) redundancy remover - 1 channel

  • Downloads


  • Single dual redundant A664P7 compatible interface using two IEEE 802.3u (100BaseTX) standard compatible Ethernet interfaces
  • Supports up to 512 virtual links
  • Filters redundant frames received within a 5ms window on the two A664P7 links; outputs exact copies of the non-redundant frames on the two output Ethernet interfaces
  • Valid frame counters, error frame counters and discarded redundant frame counters
  • Fixed latency through module


  • Filtering of dually redundant A664P7 Ethernet network traffic for recording or monitoring
  • Detection of system failures and performance problems
Acra KAM-500 chassis - 13 user-slots (extended temperature)

KAM/CHS/13U Acra KAM-500 chassis - 13 Slots

The KAM/CHS/13U/ET is a thirteen user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a power supply module which regulates power supplies for the backplane...

NET/REC/001 Ethernet Network Recorder (CompactFlash)

NET/REC/001 Ethernet Network Recorder (CompactFlash)

The NET/REC/001 is a stand-alone Ethernet network recorder. Incoming Ethernet frames are written to a CompactFlash card using a FAT32 file system.   The NET/REC/001 can be configured via...

NET/SWI/101 Ethernet Switch

NET/SWI/101 Gigabit Ethernet Switch

The NET/SWI/101 is an 8-port airborne Ethernet switch designed for operating in harsh environments. Each port is configurable for 10BaseT, 100BaseTX, and 1000BaseT link speeds or auto-negotiate...

KAD/DSI/102 Discrete input (programmable counters, time tagging) - 24 channel

KAD/DSI/102 24 channel Digital Module

The KAD/DSI/102 monitors the status (high/low) of up to 24 differential-ended discrete input channels. Each of these has an assigned programmable 32-bit counter. Additionally each of the inputs can...

KAD/VID/106 H.264 video encoder (analog video input) - 1 channel

KAD/VID/106 H.264 Video Encoder

The KAD/VID/106 is an H.264 video encoder card that converts one of three composite analog video inputs, or one Y/C analog video input to digital video and compresses it. Compressed video bit-rate...

KAD/MAT/101 Microcontroller-based module

KAD/MAT/101 Microcontroller-based module

The KAD/MAT/101 allows you run your own programs based on a dual core C6000DSP+ARM9 microcontroller. It provides high performance DSP functions in a widely used architecture. You can develop...

12 channel ADC

KAD/ADC/135 12 channel Full/½-bridge ADC

The KAD/ADC/135 is used to condition and digitize up to 12 differential ended analog channels using simultaneous sampling 16-bit A/D for each channel. At the heart of the KAD/ADC/135 is a...

KAD/ADC/136 Flexible ADC (full/½-bridge, ICP, PT100, thermocouple, FIR/IIR, 12.5 kHz b/w) - 8 channels at 50 ksps

KAD/ADC/136 8 channel Flexible ADC

The KAD/ADC/136 is used to condition and digitize up to eight analog channels. Each channel can be configured for use in differential-ended or single-ended voltage measurement, ICP sensor, RTD...


We’d like to keep in touch and send you updates on our products, news and developments – please tick below to make sure you don’t miss out. You can unsubscribe at any time by clicking on the unsubscribe link at the bottom of the emails. Your personal information will not be shared with any person or organization outside of Curtiss-Wright. Review our privacy policy.

1 Channel, ARINC 664 Part 7 (A664P7) redundancy remover

The KAD/ARR/101 is designed with two Ethernet network interfaces, which monitor network traffic on dually redundant A664P7 Ethernet links.

The A664P7 redundancy remover captures frames on the two A664P7 links and performs error checking, such as Ethernet frame check sequence and the IP header checksum, on the received frames. Valid frames are buffered to facilitate filtering of redundant frames captured on the two A664P7 links. Each A664P7 frame has a Virtual Link IDentifier (VLID) in the destination field and a sequence number, which increments by one with each frame. The first A664P7 frame on a virtual link received after reset/startup is sent to the redundancy remover. That VLID and Sequence Number (SN) are stored and any subsequent frame on that virtual link, with a sequence number equal to SN+1 or SN+2, is passed to the redundancy remover, and the new sequence number is stored. For any frames received on that virtual link with a sequence number not equal to SN+1 or SN+2, the new sequence number is stored but the frame is discarded.

Redundant copies are identified by having the same VLID and SN. The first A664P7 frame with a unique VLID and SN is sent directly to the output Ethernet interfaces. If another A664P7 frame with the same VLID and SN is received less than 5 ms later, it is considered redundant and is not output. Should a redundant copy arrive in this time frame it is removed. The filtered frames are then output unchanged on two Ethernet network interfaces after a fixed latency.


Product Finder

Connect With Curtiss-Wright Connect With Curtiss-Wright Connect With Curtiss-Wright


Contact our sales team today to learn more about our products and services.





Our support team can help answer your questions - contact us today.