KAM/CDC/101 4 channel Charge-to-digital converter

  • Downloads


  • 4 channel charge-to-digital converter for
  • piezoelectric devices
  • Programmable Input range (±100mV, ±10V)
  • Accuracy 3% FSR error from all sources typical
  • High bandwidth with programmable filters (0.5Hz to 6kHz)
  • 2nd order Butterworth 0.5Hz high pass filter
  • Standard SMC (10-32) sockets per channel
  • 16-bit simultaneous sampling on each channel
  • Up to 24K samples per second per channel
  • Up to 6K Bandwidth


  • Force and pressure measurement using piezoelectric devices
KAM-500 chassis - 9 user-slots

KAM/CHS/09U Acra KAM-500 chassis - 9 user-slots

The KAM/CHS/09U is a nine user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a power supply module which regulates power supplies for the backplane (isolated 28V...

KAD/ADC/136 Flexible ADC (full/½-bridge, ICP, PT100, thermocouple, FIR/IIR, 12.5 kHz b/w) - 8 channels at 50 ksps

KAD/ADC/136 8 channel Flexible ADC

The KAD/ADC/136 is used to condition and digitize up to eight analog channels. Each channel can be configured for use in differential-ended or single-ended voltage measurement, ICP sensor, RTD...

KAD/ADC/126 Accelerometer ADC (current excitation, programmable analog gain, 25 kHz b/w) - 4 channels at 100 ksps

KAD/ADC/126 4 channel Accelerometer ADC

The KAD/ADC/126 is used to condition and digitize up to four Single-ended (S/E) analog channels. All of these channels have a constant current source and high-pass (DC-reject) filter for use with...

KAD/ADC/129/S1 Full-bridge ADC (voltage excitation, programmable analog gain, 25 kHz b/w) - 4 channels at 100 ksps

KAD/ADC/129/S1 4 channel Full-bridge ADC

The KAD/ADC/129/S1 provides independent excitation for up to four channels. Each channel has a separate programmable amplifier, programmable filter and A/D converter. At the heart of the...

DAS Studio 3 Setup software for DAUs, network switches, recorders and ground stations

DAS Studio 3 Setup software for DAUs, network switches, recorders and ground stations

Setting up data acquisition systems can take a lot of time and effort, particularly as many systems today are growing larger and larger. Managing thousands of channels of data over dozens of data...


We’d like to keep in touch and send you updates on our products, news and developments – please tick below to make sure you don’t miss out. You can unsubscribe at any time by clicking on the unsubscribe link at the bottom of the emails. Your personal information will not be shared with any person or organization outside of Curtiss-Wright. Review our privacy policy.

4 channel, Charge-to-digital converter (piezoelectric sensors) - 4ch at 24ksps

The KAM/CDC/101 is used to digitize signals from charge-based sensors such as piezoelectric devices used for accelerometers. Each is independent and consists of a charge-to-voltage converter (charge-mode amplifier) followed by a second order high pass filter, sixth order low pass filter, programmable gain amplifier, a second order low pass filter and a separate A/D. 

At the heart of the KAM/CDC/101 is a hard-wired state-machine that over-samples all channels at a rate between 96 ksps and 192 ksps, and digitally filters any noise above the user-programmable cutoff frequency. This is achieved using cascaded, half-band, decimate by 2, 15 tap, Finite-Impulse-Response (FIR) filters with 32-bit coefficients followed by an 8th order Butterworth IIR filter with a default cutoff point set at a quarter of the sampling frequency. Unlike most Acra KAM-500 modules, the input connectors are SMC (10-32) sockets for each channel. 


Product Finder

Connect With Curtiss-Wright Connect With Curtiss-Wright Connect With Curtiss-Wright


Contact our sales team today to learn more about our products and services.





Our support team can help answer your questions - contact us today.